Gorman-rupp-pumps T3A61S-B /F,/FM Manuel d'utilisateur

OM‐05264‐01March 25, 2002Rev. K 02‐27‐13CDSTHE GORMAN‐RUPP COMPANY  MANSFIELD, OHIOwww.grpumps.comGORMAN‐RUPP OF CANADA LIMITED  ST. THOMAS, ONTARI

OM-05264SUPER T SERIESPAGE B - 3INSTALLATIONMaterialsEither pipe or hose maybe used for suction anddischarge lines; however, the materials must becomp

OM-05264 SUPER T SERIESPAGE B - 4 INSTALLATIONIf there is a liquid flow from an open pipe into thesump, the flow should be kept away from the suction

OM-05264SUPER T SERIESPAGE B - 5INSTALLATIONWith high discharge heads, it is recommended thata throttling valve and a system check valve be installed

OM-05264 SUPER T SERIESPAGE B - 6 INSTALLATIONpump can cause parts being disengaged to be ejected with great force. After the pump completely cools,

OM-05264SUPER T SERIESPAGE B - 7INSTALLATIONDISCHARGE PIPEDISCHARGECHECK VALVEPUMP DISCHARGESELF‐PRIMINGCENTRIFUGALPUMPSUCTIONLINESUPPORTBRACKETCLEAN‐

OM-05264 SUPER T SERIESPAGE B - 8 INSTALLATIONWhen checking alignment, disconnectthe power source to ensure that thepump will remain inoperative.Adjus

OM-05264SUPER T SERIESPAGE B - 9INSTALLATIONTighten the belts in accordance with the belt manufacturer's instructions. If the belts are too loos

SUPER T SERIESOM-05264OPERATION PAGE C - 1OPERATION - SECTION CReview all SAFETY information in Section A.Follow the instructions on all tags, labels

SUPER T SERIESOM-05264OPERATIONPAGE C - 2If rotation is incorrect on a three‐phase motor, havea qualified electrician interchange any two of thethree

SUPER T SERIESOM-05264OPERATION PAGE C - 3Strainer CheckIf a suction strainer has been shipped with thepump or installed by the user, check the strain

Register your newGorman‐Rupp pump online atwww.grpumps.comValid serial number and e‐mail address required.RECORD YOUR PUMP MODEL AND SERIAL NUMBERPlea

SUPER T SERIESOM-05264OPERATIONPAGE C - 4to operate properly. Make certain that the bearinglubricant is of the proper viscosity and at the correct le

SUPER T SERIES OM-05264TROUBLESHOOTING PAGE D - 1TROUBLESHOOTING - SECTION DReview all SAFETY information in Section A.Before attempting to open or se

OM-05264SUPER T SERIESTROUBLESHOOTINGPAGE D - 2TROUBLE POSSIBLE CAUSE PROBABLE REMEDYPUMP REQUIRESTOO MUCHPOWERPUMP CLOGSFREQUENTLYImpeller or other w

SUPER T SERIES OM-05264TROUBLESHOOTING PAGE D - 3TROUBLE POSSIBLE CAUSE PROBABLE REMEDYBEARINGS RUNTOO HOTBearing temperature is high, butwithin limit

OM-05264SUPER T SERIESTROUBLESHOOTINGPAGE D - 4General Condition (Temperature, UnusualNoises or Vibrations, Cracks, Leaks,Loose Hardware, Etc.) IPump

OM-05264SUPER T SERIESMAINTENANCE & REPAIR PAGE E - 1PUMP MAINTENANCE AND REPAIR - SECTION EMAINTENANCE AND REPAIR OF THE WEARING PARTS OF THE PUM

OM-05264 SUPER T SERIESMAINTENANCE & REPAIRPAGE E - 2SECTION DRAWINGPARTS PAGEDRIVE END VIEWTOP VIEWFigure 1. Pump Model T3A61S-B, Including /F, /

ITEM NO.PART NAME PART NUMBERMAT'LCODEQTY ITEM NO.PART NAME PART NUMBERMAT'LCODEQTYOM-05264SUPER T SERIESMAINTENANCE & REPAIR PAGE E - 3

OM-05264 SUPER T SERIESMAINTENANCE & REPAIRPAGE E - 4SECTION DRAWINGDRIVE END VIEWFigure 2. 44163-267 Repair Rotating Assembly

ITEM NO.PART NAME PART NUMBERMAT'LCODEQTY ITEM NO.PART NAME PART NUMBERMAT'LCODEQTYOM-05264SUPER T SERIESMAINTENANCE & REPAIR PAGE E - 5

TABLE OF CONTENTSiINTRODUCTION PAGE I - 1...SAFETY - SECTION A PAGE A - 1...

OM-05264 SUPER T SERIESMAINTENANCE & REPAIRPAGE E - 6PUMP AND SEAL DISASSEMBLYAND REASSEMBLYReview all SAFETY information in Section A.Follow the

OM-05264SUPER T SERIESMAINTENANCE & REPAIR PAGE E - 7Inspect the wear plate, and replace it if badlyscored or worn. To remove the wear plate, dise

OM-05264 SUPER T SERIESMAINTENANCE & REPAIRPAGE E - 8TEEAPPROX. 6 IN.(152 MM) LONGAPPROX. 14 IN.(356 MM) LONGFigure 4. Rotating Assembly ToolTo i

OM-05264SUPER T SERIESMAINTENANCE & REPAIR PAGE E - 9be replaced any time the shaft and bearings are removed.Clean the bearing housing, shaft and

OM-05264 SUPER T SERIESMAINTENANCE & REPAIRPAGE E - 10NOTEIf a hot oil bath is used to heat the bearings, both theoil and the container must be ab

OM-05264SUPER T SERIESMAINTENANCE & REPAIR PAGE E - 11finished faces; even fingerprints on the faces canshorten seal life. If necessary, clean the

OM-05264 SUPER T SERIESMAINTENANCE & REPAIRPAGE E - 12tainer until it slides onto the shaft and the seal facescontact.Install the seal spring, sea

OM-05264SUPER T SERIESMAINTENANCE & REPAIR PAGE E - 13NOTEIf the suction or discharge flanges were removed,replace the respective gaskets, apply `

OM-05264 SUPER T SERIESMAINTENANCE & REPAIRPAGE E - 14rotating assembly to the pump casing. Perform theback cover adjustment procedure describedab

OM-05264SUPER T SERIESMAINTENANCE & REPAIR PAGE E - 15For cold weather operation, consult the factory or alubricant supplier for the recommended g

TABLE OF CONTENTS(continued)iiTROUBLESHOOTING - SECTION D PAGE D - 1...PREVENTIVE MAINTENANCE PAGE D - 3...

For U.S. and International Warranty Information,Please Visit www.grpumps.com/warrantyor call:U.S.: 419-755-1280International: +1-419-755-1352For Canad

SUPER T SERIESOM-05264PAGE I - 1INTRODUCTIONINTRODUCTIONThank You for purchasing a Gorman‐Rupp pump.Read this manual carefully to learn how to safelyi

SUPER T SERIES OM-05264PAGE A - 1SAFETYSAFETY - SECTION AThis information applies to Super T Series basic pumps. Gorman‐Rupp has nocontrol over or pa

SUPER T SERIESOM-05264PAGE A - 2 SAFETYfumes. Wear adequate protective clothing when working on the pump or piping.Never run this pump backwards. Be

OM-05264SUPER T SERIESPAGE B - 1INSTALLATIONINSTALLATION - SECTION BReview all SAFETY information in Section A.Since pump installations are seldom ide

OM-05264 SUPER T SERIESPAGE B - 2 INSTALLATIONPREINSTALLATION INSPECTIONThe pump assembly was inspected and tested before shipment from the factory.