Gorman-rupp-pumps SE2D3 115V 1P 1483930 and up Manuel d'utilisateur

OM-06494-01August 11, 2011Rev. A 12‐13‐12THE GORMAN‐RUPP COMPANY  MANSFIELD, OHIOGORMAN‐RUPP OF CANADA LIMITED  ST. THOMAS, ONTARIO, CANADA Pri

OM-06494 SE SERIESPAGE B - 3INSTALLATIONThe pump should be independently secured andsupported by the lifting device fitted on the pump.If the applica

SE SERIESOM-06494PAGE B - 4 INSTALLATIONor death to personnel can result fromany alteration to the cable.Field Wiring Connections (Incoming Power)The

OM-06494 SE SERIESPAGE B - 5INSTALLATIONThe earth surrounding the ground rod or platemust contain enough moisture to make agood electrical connection

SE SERIESOM-06494PAGE B - 6 INSTALLATIONpump must be approved by the Gorman‐Rupp Company for the application.Motor Cable Grounding TestDo not connect

SE SERIES OM-06494PAGE C - 1OPERATIONOPERATION - SECTION CGENERAL INFORMATIONReview all SAFETY information in Section A.This pump is designed to handl

OM-06494 SE SERIESPAGE C - 2 OPERATIONPUMP OPERATIONLiquid Temperature and Overheating.Overheated pumps can cause severeburns and injury. If the pump

SE SERIES OM-06494PAGE C - 3OPERATIONAs viewed from the top, the pump should kick in acounterclockwise direction; this will indicate thatimpeller rota

OM-06494 SE SERIESPAGE C - 4 OPERATIONinto the pump casing to remove a blockage. This could result in personal injuryor damage to the equipment. If b

SE SERIES OM-06494PAGE C - 5OPERATIONBefore installing or removing the lubrication plug,always clean the area around the plug to preventcontamination.

OM-06494SE SERIESTROUBLESHOOTING PAGE D - 1TROUBLESHOOTING - SECTION DReview all SAFETY information in Section A.The following precautions should beta

Register your newGorman‐Rupp pump online atwww.grpumps.comValid serial number and e‐mail address required.RECORD YOUR PUMP MODEL AND SERIAL NUMBERPlea

SE SERIES OM-06494TROUBLESHOOTINGPAGE D - 2Table 1. Trouble Shooting Chart (cont.)TROUBLE POSSIBLE CAUSE PROBABLE REMEDYMOTOR RUNS, BUTPUMP FAILS TODE

OM-06494SE SERIESTROUBLESHOOTING PAGE D - 3ment indicated below is commercially available, oran equivalent substitute may be used.Equipment UseAmmeter

SE SERIES OM-06494TROUBLESHOOTINGPAGE D - 4male connector sleeves before reassembling the pump head to the motor housing.CapacitorThe start capacitor

OM-06494SE SERIESMAINTENANCE & REPAIR PAGE E - 1PUMP MAINTENANCE AND REPAIR - SECTION EMAINTENANCE AND REPAIR OF THE WEARING PARTS OF THE PUMP WIL

OM-06494 SE SERIESMAINTENANCE & REPAIRPAGE E - 2SECTION DRAWINGPARTS PAGEFigure E‐1. Pump Model SE2D3 115V 1P

ITEM NO.PART NAME PART NUMBERMAT'LCODEQTY ITEM NO.PART NAME PART NUMBERMAT'LCODEQTYOM-06494SE SERIESMAINTENANCE & REPAIR PAGE E - 3PARTS

OM-06494 SE SERIESMAINTENANCE & REPAIRPAGE E - 4PUMP AND SEAL DISASSEMBLYAND REASSEMBLYReview all SAFETY information in Section A.Follow the instr

OM-06494SE SERIESMAINTENANCE & REPAIR PAGE E - 5nance functions must be done by qualified personnel.Check the chart in TROUBLESHOOTING, SectionD,

OM-06494 SE SERIESMAINTENANCE & REPAIRPAGE E - 6when the seal chamber is removed. It may be necessary to heat the sleeve and tap it off the shaft

OM-06494SE SERIESMAINTENANCE & REPAIR PAGE E - 7Handle the seal parts with extreme care to preventdamage. Be careful not to contaminate the preci

TABLE OF CONTENTSiINTRODUCTION PAGE I - 1...SAFETY ‐ SECTION A PAGE A - 1...

OM-06494 SE SERIESMAINTENANCE & REPAIRPAGE E - 8Apply a light coating of oil to the seal seat bore inthe seal chamber (9). Position the stationary

OM-06494SE SERIESMAINTENANCE & REPAIR PAGE E - 9See VACUUM/PRESSURE TESTING and LUBRICATION before putting the pump back intoservice.MOTOR DISAS

OM-06494 SE SERIESMAINTENANCE & REPAIRPAGE E - 10rotor is removed.See Head And Power Cable Installation if no further disassembly is required.Rot

OM-06494SE SERIESMAINTENANCE & REPAIR PAGE E - 11dling the stator, do not set it on the end windings;lay it on its side.Do not attempt to rewind t

OM-06494 SE SERIESMAINTENANCE & REPAIRPAGE E - 12After the stator is fully and squarely seated on themotor housing shoulder, remove the expandable

OM-06494SE SERIESMAINTENANCE & REPAIR PAGE E - 13this pump is high enough to cause injury or death. Make certain that the plugon the pump power c

OM-06494 SE SERIESMAINTENANCE & REPAIRPAGE E - 14VACUUM/PRESSURE TESTINGTo ensure the water‐tight integrity of the pump, it isrecommended that the

OM-06494SE SERIESMAINTENANCE & REPAIR PAGE E - 15when the pump is hot, pressure in theseal cavity can cause hot oil to beejected as the plug is re

For U.S. and International Warranty Information,Please Visit www.grpumps.com/warrantyor call:U.S.: 419-755-1280International: +1-419-755-1352For Canad

TABLE OF CONTENTS(continued)iiPUMP END DISASSEMBLY PAGE E - 4...Strainer And Impeller Cover Removal PAGE

SE SERIES OM-06494PAGE I - 1INTRODUCTIONINTRODUCTIONThank You for purchasing a Gorman‐Rupp pump.Read this manual carefully to learn how to safelyinsta

SE SERIES OM-06494SAFETYPAGE A - 1SAFETY - SECTION AThis information applies to SE Seriessubmersible motor driven pumps.Because pump installations are

OM-06494 SE SERIESPAGE A - 2 SAFETYconflict between the instructions provided and N.E.C. Specifications, N.E.C.Specifications shall take precedence.A

OM-06494 SE SERIESPAGE B - 1INSTALLATIONINSTALLATION - SECTION BGENERAL INFORMATIONReview all SAFETY information in Section A.Since pump installation

SE SERIESOM-06494PAGE B - 2 INSTALLATIONPUMP INSTALLATIONPump Motor SpecificationsSee Tables B‐1 and B‐2 for pump specifications.Table B‐1. Pump Speci